Step Instruction for Installing a Bathtub
Step Instruction for Installing a Bathtub
Blog Article
We have stumbled on this post relating to How to Install a Bathtub below on the net and decided it made sense to write about it with you in this article.
Mounting a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the project can relocate easily; if you need to open a wall surface to get rid of the old tub and position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's skills, although you will require an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have certified yourself for the task and fit trying it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to consider employing one prior to you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will aid you install a brand-new tub in your shower room if you have currently bought a brand-new bathtub as well as do not require to change the arrangement of your previous water supply pipes.
Your devices and material list should make up the following:
Planning for the Setup
Firstly, the supporting frame supplied with the bathroom should be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of getting rid of the existing taps can be quite problematic because of the restricted gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Before proceeding to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of both wood boards under its feet, put the tub in the required setting. The wood boards are useful in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bath tub till the spirit level reviews level.
To install taps, fit the bottom of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and examine all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill up the bath tub as well as also inspect the overflow outlet and also the normal electrical outlet for leakages.
Lastly, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has been utilized a minimum of once as this will resolve it right into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines remain in area between the faucet and the sink. Protect the faucet in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular faucet adapters. The previous type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a rigid seal, causing the water to penetrate the wall surface in between the bath and also the tiling, causing complications with wetness and feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can break fairly early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily readily available on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was introduced to that report about How to Install a Bathtub Yourself through someone on another website. Those who liked our blog posting please remember to share it. Thanks for your time invested reading it.
Ensure plumbing integrity; reach out. Report this page